View GRM21BR61A106KE19L_4575799.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

evaluation board user guide ug - 272 one technology way ? p. o . box 9106 ? norwood, ma 02062 - 9106, u.s.a. ? tel: 781.329.4700 ? fax: 781.461.3113 ? www.analog.com evaluating the ad983 3 low power 12.65 mw , 2.3 v to 5.5 v , programmable waveform generator please see the last page for an important warning and legal terms and conditions . rev. a | page 1 of 12 features full featured evaluation board for the ad9833 evaluation board graphic al user interface software for board control and data analysis connector to eval - sdp - cb1z system demonstration platform (sdp) board various power supply and reference link options applications biomedical sensors bioelectrical impedance analysis electrochemical analysis impedance spectroscopy complex impedance measurement nondes tructive testing general description the ad9833 is a 25 mhz low power dds device capable of producing high performance sine and triangular outputs. it also has an on - board comparator that allows a square wave to be produced for clock generation. consuming only 13 mw of power at 3 v makes the ad9833 an ideal candidate for power - sensitive applications. the eval - ad983 3 sdz board is used in conjunction with a n e va l - sdp - cb1z sdp board available from analog devices, inc. the usb - to - spi communication to the ad9837 is completed using this blackfin? - based development board. a high performance, on - board 25 mhz trimmed general oscillator is available to use as the master clock for the ad9837 system. various links and smb connectors are also available on the eval - ad983 3 sdz board to maxim ize usability. complete specifications for the ad9833 are provided in the ad9833 data sheet, available from analog devices, and should be consulted in conjunction with this user guide when using the evaluation board. functional block dia gram sdata fsync mclk ad9833 eval-sdp-cb1z ref196 usb sport vout mclk xo sclk 09812-001 figure 1.
ug- 272 evaluation board user guide rev. a | page 2 of 12 table of contents features .............................................................................................. 1 applications ....................................................................................... 1 general description ......................................................................... 1 functional block diagram .............................................................. 1 revision history ............................................................................... 2 evaluation board software .............................................................. 3 installing the software ................................................................. 3 running the software .................................................................. 4 using the evaluation board software ............................................ 5 setting up the digital interface .................................................. 5 select external mclk frequency ...............................................6 loading frequency and phase registers ....................................6 fsk and psk functionality ..........................................................6 waveform options ........................................................................6 reset and sweep ............................................................................7 ex ample of operation ...................................................................7 evaluation board schematics and layout ......................................8 ordering information .................................................................... 10 bill of materials ........................................................................... 10 revision history 8 /1 2 rev . 0 to rev. a change to table 1 ............................................................................. 4 4 / 11 rev ision 0: initial version
evaluation board user guide ug- 272 rev. a | page 3 of 12 evaluation board software installing t he software t he eval - ad983 3 sdz evaluation kit i ncludes the software and drivers on cd. the software is compatible with windows? xp, windows vista, and windows 7. to install the software, follow these steps: 1. install the software before connecting the sdp board to the usb port of the pc. 2. start the wind ows operating system and insert t he e va l - ad983 3 sdz evaluation kit cd. 3. download the ad983 3 sdz labview ? software. the correct driver, sdpdriversnet, for the sdp board should download automatically after labview is download ed , supporting both 32 - and 64 - bit systems. however, if the drivers do not download automatically, the driver executable file can also be found in the program files / analog devices folder. follow the on - screen prompts to install the sdpdrivernet version 1.3.6.0. 4. after installation of the sof tware and drivers is complete, plug the eval - ad983 3 sdz into the sdp board and the sdp board into the pc using the usb cable included in the box. 5. when the software detects the evaluation board, proceed through any dialog boxes that appear to finalize the in stallation ( found new hardware wizard / install the software automatically and so on). 09812-002 figure 2 . hardware device manager window with sdp board plugged in
ug- 272 evaluation board user guide rev. a | page 4 of 12 running the software to run the evaluation board program, do t he following: 1. click start/all programs/analog devices/ad983 3 / ad983 3 eval board . 2. if the sdp board is not connected to the usb port when the software is launched, a connectivity error displays (see figure 3 ). simply connect the ev aluation board to the usb port of the pc, wait a few seconds, click rescan , and follow the instructions. 3. ensure that all links are in their correct locations (see table 1 ). the main window of the ad983 3 dbz evaluati on software then opens, as shown in figure 4 . table 1 . default setup for link positions link no. position function lk1 out decouple the cap/2.5v pin to ground because v dd is >2.7 v. lk2 a on - board linear regulator selected to supply power to the general oscillator. lk4 a 3.3 v digital supply for the ad9833 supplied from the eval - sdp - cb1z sdp board. 09812-003 figure 3 . pop - up window error
evaluation board user guide ug- 272 rev. a | page 5 of 12 using the evaluation board sof tware 09812-004 figure 4 . ad983 3 dds evaluation software setting up the digit al interface the first software step in setting up the ad9833 to make some measurements is to set the digital interface value . the e va l - sdp - cb1z has two connectors plugs: connectora and connectorb . select the connector you want to use with the ad983 7 evaluation board from the drop - down box . the spi frame frequency (/sync) box and sclk frequency box can also be set in this window. if the spi interface speed has not been decid ed, leave the default values shown in figure 5 . 09812-005 figure 5 . digital interface
ug- 272 evaluation board user guide rev. a | page 6 of 12 select external mclk frequency having selected the digital interface specifics, next use the external mcl k box to choose which frequency to use. the boards are supplied with a 2 5 mhz general oscillator. if a different clock source is required, the clk1 smb connector can be used to supply a different mclk value. two options for the general oscillator include the ael3013 oscillators from ael crystals and the sg - 310scn oscillators from epson electronics. 09812-006 figure 6 . external mclk input loading frequency an d phase registers the desired output frequency and output phase can be loaded using the inputs shown in figure 7 . either the freq 0 register or the freq 1 register can be loaded with frequency data. the frequency data is loaded in megahertz , and the equivalent hex code is shown to the right once data is entered; click enter to load data. once data is loaded, the output appear s on the iout1 and iout2 pins. similarly, either the phase 0 register or phase 1 register can be selected, and the phase data is loaded in degrees. the analog output frequency from the ad9833 is defined by f mclk /2 28 freqreg where freqreg is the value loaded into the selected frequency register in decimals. this signal is phase shifted by 2/4096 phasereg where phasereg is the val ue contained in the selected phase register in decimals. 09812-007 figure 7 . frequency and phase load fsk and psk function ality in software mode, the ad9833 can be set up for fsk or psk functiona lity by simply entering the bit rate in milliseconds and selecting the push - button option (see figure 8 ). 09812-008 figure 8 . fsk and psk functionality waveform options the output waveform can be selected as a sin usoidal waveform or a ramp waveform. the internal comparator in the ad9833 can be disabled or enabled (see figure 9 ). the msb or the msb/2 of the phase accumulator can be selected as the output on the sign bit out pin. 09812-009 figure 9 . waveform profile and sign bit out pin power - down options the ad9833 has various power - down options selected through the contro l register. the part can disable the mclk or disable the dac if just the msb output is used on the sign bit out pin, or it can power down both sections for a lower power sleep mode (see figure 10). 09812-010 figure 10 . power - down options
evaluation board user guide ug- 272 rev. a | page 7 of 12 reset and sweep the reset software command is set using the button shown in figure 11 . to s e t up a dds sweep, click sweep . 09812-0 1 1 figure 11 . s oftware reset and sweep select the sweep function allows users to load a start frequency, stop frequency, increment size, number of loops, and delay between each frequency increment. these commands are then loaded to the part automatically from the e va l - sdp - cb1z board. 09812-012 figure 12 . sweep functionality example of operation an example of configuring the ad983 3 to output 10 khz follows: 1. plug the e va l - sdp - cb1z board into the eval - ad983 3 sdz board and connect to the usb port. 2. start up the software located at start / all programs / analog devices / ad983 3 / ad983 3 eval board . you should see the sdp board communicatin g with the pc. 3. select connectora or connectorb ; this must match what the ad983 7 test chip is connected to. 4. define mclk; the default is an on - board 25 mhz oscillator. 5. ensure that all links are in the correct locations (see table 1 ). 6. select the freq 1 register. 7. load a 10 khz excitation frequency and click enter . the output should appear on the iout and ioutb outputs on the evaluation board. for the freq 0 register, ? select the freq 0 register. ? load the freq 0 registe r with 20 khz and click enter . for the freq 1 register, ? select the freq 1 register to load the 10 khz associated with this register. ch1 100mv m20 s a ch1 182mv 1 t 0s ch1 freq 10khz ch1 p-p 596mv 09812-013 figure 13 . 10 khz output signals on an iout test point
ug- 272 evaluation board user guide rev. a | page 8 of 12 evaluation board sch ematics and layout 09812-014 figure 14 . ad983 3 schematic part a
evaluation board user guide ug- 272 rev. a | page 9 of 12 09812-015 figure 15 . ad983 3 schematic part b 09812-016 figure 16 . evaluation board layout
ug- 272 evaluation board user guide rev. a | page 10 of 12 ordering information bill of materials table 2 . reference designator description manufacturer part number c1, c2, c4 to c7, c8 0.1 f , 50 v , x7r ceramic capacitor murata grm188r71h104ka93d c3 0 .01 f ceramic capacitor, 0603, 10 v, x5r, 10% kemet c0603c103k5ractu c9 , c10, c11 10 f smd t antal um c apacitor, 10 v, 10%, rtaj_a avx taja106k010r c16 1 f ceramic capacitor, 10 v , 10% , y5v , 0603 murata cc0603zry5v6bb105 c17, c19 0.1 f capacitor , 0603, 16 v, x7r, 10% multicomp b0603r104kct c18 10 f ceramic capacitor, 10 v , 10% , x5r , 0805 murata GRM21BR61A106KE19L clk1, vout1 straight pcb m ount smb j ack , 50 ? tyco 1 - 1337482-0 fsync, sclk, sdata, vout, vout2 red t est point vero 20- 313137 j1 120- way c onnector, 0.6 mm p itch, r eceptacle hrs (hirose) fx8 - 120s - sv(21) j3, j4 2 -p in t erminal b lock (5 mm p itch) campden ctb5000/2 lk1 jumper block, 2 - pin 0.1" sp acing harwin m20 - 9990246 lk2, lk4 3 -p in sil h eader and s horting l ink harwin m20 - 9990345 and m7567 -05 r4 50 ? smd resistor, 0603 multicomp mc 0.063w 0603 50r r5, r6 0 ? smd r esistor , 0603 multicomp mc 0.063w 0603 0r u1 64k i 2 c s erial eeprom msop -8 micro chip 24lc64 - i/ms u2 precision micropower, low dropout, low voltage references, 8 - lead tssop analog devices ref196gruz u3 low power 12.65 mw, 2.3 v to 5.5 v, programmable waveform generator , 10 - lead msop analog devices ad9833 brmz x tal1 25 mhz ael cryst als x tal -ael -301 - series
evaluation board user guide ug- 272 rev. a | page 11 of 12 notes
ug- 272 evaluation board user guide rev. a | page 12 of 12 notes esd caution esd (electrostatic discharge) sensitive device . charged devices and circuit boards can discharge without detection. although this product features patented or proprietary protection circuitry, damag e may occur on devices subjected to high energy esd. therefore, proper esd precautions should be taken to avoid performance d egradation or loss of functionality. legal terms and conditions by using the evaluation board discussed herein (together with any tools, components documentation or support materials, the evaluation board), you are agreeing to be bound by the terms and conditions set forth below (agreement) unless you have purchased the evaluation board, in which case the analog devices standard terms and conditions of sale shall govern. do not use the evaluation board until you have read and agreed to the agreement. your use of the evaluation board shall signify your acceptance of the agreement. this agreement is made by and between you (custom er) and analog devices, inc. (adi), with its principal place of business at one technology way, norwood, ma 02062, usa. subject to the terms and conditi ons of the agreement, adi hereby grants to customer a free, limited, personal, temporary, non - exclusi ve, non - sublicensable, non - transferable license to use the evaluation board for evaluation purposes only. customer understands and agrees that the evalu ation board is provided for the sole and exclusive purpose referenced above, and agrees not to use the e valuation board for any other purpose. furthermore, the license granted is expressly made subject to the following additional limitations: customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the evaluation bo ard; and (ii) permit any third party to access the evaluation board. as used herein, the term third party includes any entity other than adi, customer, their employees, affiliates and in - house consultants. the evaluation board is not sold to customer; all rig hts not expressly granted herein, including ownership of the evaluation board, are reserved by adi. confidentiality. this agreement and the evaluation board shall all be considered the confidential and proprietary information of adi. customer may not discl ose or transfer any portion of the evaluation board to any other party for any reason. upon discontinuation of use of the eva luation board or termination of this agreement, customer agrees to promptly return the evaluation board to adi. additional restrict ions. customer may not disassemble, decompile or reverse engineer chips on the evaluation board. customer shall inform adi of any occurred damages or any modifications or alterations it makes to the evaluation board, including but not limited to soldering or any other activity that affects the material content of the evaluation board. modifications to the evaluation board must comply with applicable law, including but not limited to the rohs directive. termi nation. adi may terminate this agreement at any ti me upon giving written notice to customer. customer agrees to return to adi the evaluation board at that time. limitation of liability. the evaluation boar d provided hereunder is provided as is and adi makes no warranties or representations of any kind w ith respect to it. adi specifically disclaims any representations, endorsements, guarantees, or warranties, express or implied, related to the evaluation board including, but not limited to, the implied warranty of merchantability, title, fitness for a par ticular purpose or noninfringement of intellectual property rights. in no event will adi and its licensors be liable for any incidental, special, indirect, or consequential dam ages resulting from customers possession or use of the evaluation board, includ ing but not limited to lost profits, delay costs, labor costs or loss of goodwill. adis total liability from any and all cau ses shall be limited to the amount of one hundred us dollars ($100.00). export. customer agrees that it will not directly or indire ctly export the evaluation board to another country, and that it will comply with all applicable united states federal laws and regulations relating to exports. governing law. this agreement shall be governed by and const rued in accordance with the substa ntive laws of the commonwealth of massachusetts (excluding conflict of law rules). any legal action regarding this agreement will be heard in the state or fede ral courts having jurisdiction in suffolk county, massachusetts, and customer hereby submits to t he personal jurisdiction and venue of such courts. the united nations convention on contracts for the international sale of g oods shall not apply to this agreement and is expressly disclaimed. ? 2011 C 2012 ana log devices, inc. all rights reserved. trademarks and registered trademarks are the property of their respective owners. ug09812 - 0 - 8/12(a)

▲Up To Search▲

Price & Availability of GRM21BR61A106KE19L

	To Download GRM21BR61A106KE19L Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .